CAUTION: First, read the safety instructions to prevent hazards of fatal electrical shock and fire.

NOTE: As long as the machine has not completed the priming, it will not produce any coffee.

Descaling is mandatory when the machine indicates that this is required (blinking "Descaling" alert indicator light). If descaling is not performed, after 30 cycles, the "Descaling" alert indicator light lights up steadily and the machine locks itself until the descaling is performed.

When unpacking the machine, place it on a horizontal, stable, uncluttered work surface.

Remove the water tank, drip tray, drip base and capsule container. Remove the milk frother from its storage.

Position the cord to the right or left of the machine (according to your preference) by using the housing intended for this purpose under the machine.

Plug the machine into the mains.

Rinse the water tank before filling it with fresh drinking water.

Place the water tank in its base, then insert the capsule container and the drip tray. Place the milk frother.

NOTE: Refer to the "Assembly/Disassembly of the milk frother" paragraph.

Turn on the machine by pressing one of the 9 keys for 1 second.

The 9 recipes keys blink. The machine is in startup mode. If only 3 keys are blinking, check that the milk frother is properly inserted.

Place a container (600ml) under the head.

Lift the lever and leave it in an open position.

Press one of the 9 keys. The 9 keys blink quickly.

NOTE: Some water may flow from the milk frother for a few seconds.

Priming is completed. Lower the lever.

Light will blink while the machine is heating up. Steady light indicates the machine is ready for rinsing.

Press the Lungo key to rinse the machine. Repeat this operation three times. Next, press the Hot Foam key to clean the steam circuit. The machine is ready for use.

NOTE: All our machines are fully tested after having been manufactured. Traces of coffee may be visible in rinising water.

CAUTION: Never lift the lever during operation and refer to the important safeguards to avoid possible harm when operating the appliance.

Turn on the machine by pressing one of the coffee keys (Ristretto, Espresso, Lungo)

Lift the lever completely and insert capsule.

Close the lever and place a cup under the coffee outlet.

Adjust the position of the drip tray according to your cup. Make sure the drip tray is properlt placed.

Press the Ristretto, Espresso or Lungo key. The selected key blinks while coffee is flowing and lights up steadily once the recipe is done. The preparation will stop automatically. To stop the coffee flow at any time, press the selected recipe again.

NOTE: To top up your coffee, press the selected recipe again.

Once preparation is done, take the cup. Lift and close the lever to eject the capsule.

NOTE: while the machine turns on, you may press any coffee key. The coffee will automatically flow as soon as the machine is ready.

NOTE: This step consists of defining the water hardness (i.e. the limestone level) so that the machine personalises how frequently descaling is performed. The water hardness level can be tested with the water hardness stick available on the first page of the user manual. The water hardness is set at 4 by factory default

Wet it in the water that you will be using. Analyse the water hardness level using the water hardness table.

Turn on the machine by pressing one of the 9 keys for 1 second.

Simultaneously press the Cold Foam + Mocha keys for 3 seconds: the "Descaling" and "Clean" alert indicator lights light up and the Lungo, Hot Foam, Cold Foam, Espresso and Latte Macchiato keys blink.

Press the key that matches the hardness measured. The key blinks 3 times to confirm the new selected value.

The machine automatically exits from the Water Hardness Setting Menu mode.

NOTE: the Water Hardness Setting Menu mode deactivates after 15 seconds inactivity.

Remove the water tank.

Remove the milk frother from its housing behind the machine.

Lift up the head. Insert the milk frother in the connection and push it in all away. The milk-base recipes keys will light up when the milk frother is dected.

Once the prepartion is completed, the "Clean" alert lights up in orange.

Lift up the head, remove the milk frother by means of its grip area, and the "Clean" indicator light turns off. Clean the milk frother by dishwashing or hand washing with mild / soft detergent. Put the milk frother back in its housing.

Be sure to wait for the end of the preparation and the "Clean" indicator light to light up before handling the milk frother. It is important to take milk frother by its grip area intended for this purpose because the milk frother may be hot after preparation

NOTE: For perfect foam, use refrigerated UHT or pasteurized milk skimmed or semi-skimmed (approximately 4°C).

You can use soy, almond or oat drink for your milk preparations.

The volume of milk foam depends on the nature of the milk used, its temperature, the cup and the position of the milk frother in the mug.

It is required to clean the milk frother after each recipe. Refer to the "Daily Maintenance” paragraph

CAUTION: For the recipes using ice cubes, pieces of chocolates, ensure that they do not impede the milk frother's motion during the preparation of the recipe.

When positioning the milk frother in your mug, ensure that it is not in contact with the sides or bottom of your mug

To prevent any overflow, it is strongly recommended to respect the following instructions.

For perfect results when making your milk-based recipe, it is recommended to use the Nespresso View Mug (270 ml) found in the box and available in your Nespresso boutique

Lift up the head using the handle and place the milk frother

NOTE: Refer to the “Assembly/Disassembly of the milk frother” paragraph.

Put the ingredients and the milk according to the recipe you want to prepare in your VIEW mug (see the recipes page). Place it under the head and lower the head until the milk frother is immersed.

Only when preparing a milk recipe with coffee, completely lift the lever and insert a capsules. Close the lever.

Press the recipe key. The milk frothing starts automatically. The selected recipe key blinks slowly while it is being prepared.

Only when preparing a recipe with coffee: once the milk frothing is done, the coffee will automatically flow.

NOTE: The Espresso key lights up at the end of the preparation for top up your coffee.

Once the preparation is completed, the "Clean" indicator light lights up orange. Lift up the head, remove the milk frother by means of its grip area. The "Clean" indicator light turns off. Clean the milk frother by diswashing or hand washing. Put the milk frother back in its housing

NOTE: Be sure to wait for the end of the preparation and the "Clean" indicator light to light up before handling the milk frother. It is important to take the milk frother by its grip area intended for this purpose because the milk frother may be hot after completion of preparation

Take the cup. Lift and close the lever to eject the capsule when preparing a recipe with coffee.

NOTE: For perfect foam, use refrigerated UHT or pasteurized milk skimmed or semi-skimmed (approximately 4°C).

You can use soy, almond or oat drink for your milk preparations.

The volume of milk foam depends on the nature of the milk used, its temperature, the cup and the position of the milk frother in the mug.

It is required to clean the milk frother after each recipe. Refer to the "Daily Maintenance” paragraph

CAUTION: For the recipes using ice cubes, pieces of chocolates, ensure that they do not impede the milk frother's motion during the preparation of the recipe.

When positioning the milk frother in your mug, ensure that it is not in contact with the sides or bottom of your mug

To prevent any overflow, it is strongly recommended to respect the following instructions.

When using your personal cup, you need to follow these 4 rules in order to ensure the recipe quality and prevent overflow during the preparation.

Lift the head of the machine and place the milk frother.

NOTE: Refer to the “Assembly/Disassembly of the milk frother” paragraph.

Put the drip tray on the high position. If your mug is too tall to fit under the head of the machine, place the drip tray in the low position or remove the drip tray.

Put in your cup the ingredients and the milk according to the recipe that you want to prepare, place it under the head of the machine and lower it.

If the milk frother isn’t immersed in the milk, ajust the quantity of milk in a way that it reaches the surface of the milk frother. The milk must never fill more than half of the cup.

Only when preparing a milk recipe with coffee, completely lift the lever and insert a capsules. Close the lever.

Press the recipe key. The milk frothing starts automatically. The selected recipe key blinks slowly while it is being prepared.

Only when preparing a recipe with coffee: once the milk frothing is done, the coffee will automatically flow.

NOTE: The Espresso key lights up at the end of the preparation for top up your coffee

Once the preparation is complete, the "Clean" indicator light lights up orange. Lift up the head, remove the milk frother by means of its grip area. The "Clean" indicator light turns off. Clean the milk frother.

NOTE: Be sure to wait for the end of the preparation and the "Clean" indicator light to light up before handling the milk frother. It is important to take the milk frother by its grip area intended for this purpose because the milk frother may be hot after completion of a preparation.

Turn on the machine by pressing one of the coffee keys (Ristretto, Espresso, Lungo).

Lift the lever completely and insert a capsule

Close the lever and place a cup under the coffee outlet.

Press and hold the Ristretto, Espresso or Lungo key. Release the key as soon as the desired volume is reached.

The programmed key blinks rapidly 3 times to confirm the new setting. The coffee volume level is now stored.

NOTE: We recommend that you maintain the factory settings for Ristretto, Espresso and Lungo to ensure the best results in your cup for all our black coffees.

Turn on the machine by pressing one of the coffee keys (Ristretto, Espresso, Lungo).

Simultaneously press the Lungo and Mocha keys for 3 seconds to activate the Factory Settings Menu. The Lungo and Mocha keys blink 3 times.

The factory settings are restored. The machine automatically exits from the Factory Settings Menu mode.

NOTE: The machine will turn into OFF mode automatically after 9 minutes of non-use.

Turn on the machine by pressing one of the coffee keys (Ristretto, Espresso, Lungo).

Simultaneously press the Hot Foam + Cappuccino keys for 3seconds to go to the Automatic Power Saving Setting menu: the "Descaling" and "Clean" alert indicator lights are lit, and the Hot Foam, Latte Macchiato and Cappuccino keys blink

Press one of the Hot Foam, Latte Macchiato and Cappuccino keys to select the desired automatic power off time. You have 15 seconds to program the desired value by pressing the corresponding key.

The programmed key blinks 3 times to confirm the new selected value.

The machine automatically exits from the Automatic Power Saving Setting Menu mode.

NOTE: the Automatic Power Saving Setting Menu mode deactivates after 15 seconds of inactivity.

NOTE: Do not use any aggressive or solvent-based cleaning products. Use a non-abrasive damp cloth and a gentle cleaning agent to clean the surface of the machine. Do not wash any of the machine’s components in the dishwasher, except for the milk frother and the capsule container.

Lift and close the lever to eject the capsule. Remove the milk frother.

Gently pull on the drip tray to remove the drip base and the capsule container at the same time. Empty them, rinse them using drinking water, dry them using a clean, damp cloth, then put them back in place

NOTE: The milk frother and capsule container can be washed in a dishwasher.

Remove the water tank, fill it with fresh drinking water. Place a container under the coffee outlet (600 ml), press the Lungo key to rinse the machine.

Clean the coffee outlet and the milk frother connection using a clean, damp cloth.

Clean the machine using a clean, damp, non-abrasive cloth.

CAUTION: Refer to the safety instructions

NOTE: To ensure the proper operation of your machine throughout its service life and to maintain a coffee experience as perfect as on its first day, we recommend the following instructions. Descaling is mandatory when the machine indicates that this is required (blinking "Descaling" alert indicator light). To protect your machine's internal components, if descaling is not performed, after 30 cycles, the "Descaling" alert indicator light lights up steadily and the machine locks itself until the descaling is performed.

Descale your machine when the "Descaling" alert indicator light blinks

Lift and close the lever to eject the capsule

Empty the drip tray, drip base and capsule container. Fill the water tank with 500 ml of fresh drinking water. Pour 1 pouch of Nespresso liquid descaling agent into the water tank.

Insert the milk frother.

NOTE: Refer to the "Assembly/Disassembly of the milk frother” paragraph.

Place a minimum 1L container under the head.

To enter the descaling mode, simultaneously press the Lungo + Ristretto keys for 3 seconds. Both keys blink. To start the descaling program press the same keys again

NOTE: The "Descaling" alert indicator light stays lit orange during the entire descaling process.

NOTE: Once in descaling mode, the procedure below must be fully performed so that the machine may return to the normal mode. Any interruption (stoppage of the machine, power outage, etc.) will return the machine to the start of the descaling phase.

The descaling liquid alternatively flows from the coffee outlet and from the milk frother

Once the descaling cycle is done (the water tank is empty), the Lungo + Ristretto keys blink

Rinse the water tank and completely fill it with fresh drinking water

Press the Lungo + Ristretto keys again. Rinsing continues via the coffee outlet and the milk frother. The Lungo + Ristretto keys blink.

Once rinsing is done, the machine goes back to ready mode and the "Descaling" alert indicator light shuts off. Remove and store the milk frother in its housing. Fill the water tank with fresh drinking water.

Clean the machine using a damp cloth. You have completed the machine’s descaling.

NOTE: This function empties air from the machine to ensure the quality of the preparations. As a safety measure, the machine may block use if there is any air present.

Insert the milk frother.Turn on the machine by pressing one of the 9 keys for 1 second.

CAUTION: The milk frother must be inserted before starting the procedure.

The 9 recipes keys blink non-stop.

Place a container (600 ml) under the head of the machine.

Lift the lever and leave it in an open position

Fill the water tank and put it back in place.

Press one of the 9 keys. The 9 keys blink quickly.

Some water may flow from the milk frother for a few seconds.

Once priming is completed, the machine returns to “Ready for use” mode